Tài Liệu Kỹ Thuật
Hướng dẫn lắp đặt, sách hướng dẫn vận hành, quy trình bảo trì và tài liệu khắc phục sự cố cho thiết bị sản xuất ống xi măng.
HLY-INS-01: Suspension Roller Pipe Machine Foundation & Installation Manual
1. Scope & Equipment Overview This manual governs the civil foundation construction, mechanical alignment, and anchoring of HLY single-station and dual-station suspension roller co...
HLY-INS-02: CNC Rebar Cage Welding Machine Commissioning & Wiring Guide
1. Machine Bed & Rail Installation - Longitudinal Rail Straightness: The total straightness deviation of the servo carriage travel rails must be $\le$ 1.0 mm over full length, with...
HLY-INS-03: JS Series Twin-Shaft Mixer Assembly & Pneumatic Calibration
1. Structural Leg Positioning & Anti-Overturning Bracing - Elevate mixer legs (clearance 3.8m or 4.5m for batch transfer hopper) with verticality deviation $\le$ 1/1000. - Perimete...
HLY-INS-04: Gantry Crane Track Foundation Leveling & Festoon Cable Installation
1. Crane Rail Foundation & Alignment Tolerances - Heavy-duty P43 or P50 crane rails fastened upon continuous concrete grade beams. - Span Gauge Tolerance: Actual track gauge vs nom...
HLY-OP-01: Suspension Roller Machine Console Dual-Speed & Auto-Feeding SOP
1. Pre-Shift 5-Minute Safety Checklist 1. Verify hydraulic tank oil level is at 2/3 of sight glass and temperature is between 20°C and 50°C. 2. Check main reducer oil level and con...
HLY-OP-02: CNC Rebar Cage Welder Touchscreen Programming & Resistance Welding SOP
1. HMI Touchscreen Recipe Programming 1. Navigate to "Recipe Setup", load target standard profile (e.g., DN1000-GB2.5M). 2. Input dimensional parameters: - Total cage length (e....
HLY-OP-03: 4-Stage Steam Curing Thermal Valve Control & Recording SOP
1. Pit Enclosure & Pre-Steaming Delay - Place green pipes into pit; lower insulated covers; verify water-trough perimeter seals are flooded to prevent steam escapes. - Mandatory De...
HLY-OP-04: Hydraulic Collapsible Box Culvert Mold Stripping & Clamping SOP
1. Pre-Pour Setup & Mechanical Wedging 1. Spray bio-based release oil over inner core and outer formwork panels. 2. Start hydraulic station (set to 18 MPa); shift lever to "Expand"...
HLY-MNT-01: Precast Concrete Pipe Mold Daily Cleaning & End-Ring Alignment Protocol
1. Mandatory 15-Minute Post-Demolding Cleaning Rule - Within 15 minutes of pipe stripping, crews must remove cement paste with pneumatic scrapers and curved brass blades. - Zero Ha...
HLY-MNT-02: Twin-Shaft Mixer Wear Liner Replacement, Clearance Adjustment & Seal Greasing
1. Blade-to-Liner Operating Clearance Adjustment - Inspect gap between blade tips and curved wear liners weekly; maintain between 3.0 and 5.0 mm. - If clearance exceeds 8.0 mm, loo...
HLY-MNT-03: Suspension Roller Main Drive Shaft NDT Inspection & Roller Bearing Greasing
1. Ultrasonic Non-Destructive Testing (NDT) of Roller Shaft - The 42CrMo forged alloy steel roller shaft endures multi-ton alternating dynamic loads. - Conduct ultrasonic flaw dete...
HLY-MNT-04: Specialized C-Hook Pipe Lifter & Spreader Beam Rigging NDT Inspection
1. Monthly Magnetic Particle Testing (MT) of Welded Roots - The 90° re-entrant throat corner of counterbalanced C-hooks endures peak tensile concentrations. - Inspect all critical ...
HLY-TS-01: Pipe Delamination, Spiral Cracks & Mold Jumping Troubleshooting Guide
Fault 1: Severe Mold Hopping & Impact Noise on Roller Shaft - Root Causes: 1. Non-uniform longitudinal feeding causing dynamic mass imbalance; 2. Runner rings worn out-of-round...
HLY-TS-02: CNC Cage Welder Weld Failures, Pitch Drift & Servo Alarm Diagnosis
Fault 1: Cold Welds, Lack of Fusion & Brittle Joint Separation - Root Causes: 1. Low pneumatics (<0.4 MPa) providing inadequate squeeze pressure; 2. Heavy rust scale, drawing o...
HLY-TS-03: Steam Curing Thermal Shocks, Crazing Cracks & Strength Retrogression Fixes
Fault 1: Spiderweb Crazing Cracks on Pipe Surfaces Post-Curing - Root Causes: 1. Pre-steaming delay too short; pore water flashes to steam prior to initial set; 2. Superheated ...
HLY-TS-04: Hydraulic Core Jamming, Sync Cylinder Pressure Drop & Release Manual
Fault 1: Inner Core Locked Solid During Collapse Cycle (Pump Stalls at Relief) - Root Causes: 1. Cement slurry intruded into corner wedge slider grooves and set rock-hard; 2. M...
HLY-GEN-01: Three-Edge Bearing Load Testing & Hydrostatic Proof Standards
1. Three-Edge Bearing Test (TEBT, ASTM C497 / GB/T 16752) - Apparatus Setup: Rigid loading frame, upper loading beam, lower parallel hardwood timber strips (width 50 mm, spaced at ...
HLY-GEN-02: Dry-Cast Zero-Slump Concrete Mix Design & Vebe Consistency Norms for Precast Plants
1. Binder Quantity & Water-Cement Ratio Redlines - Cement Grade: Ordinary Portland Cement (OPC Grade 42.5 or 52.5), dosage 320–380 kg/m³. - Water-Cement Ratio (W/C): Strictly maint...
HLY-GEN-03: Trenchless Jacking Pipe Manufacturing Tolerances & Steel Collar Inspection Protocol
1. Jacking Pipe Manufacturing Tolerance Limits - End Face Squareness: Perpendicularity deviation must be $\le$ 0.8 mm (exceeding 1.0 mm causes catastrophic edge spalling under high...
HLY-GEN-04: Pipe Storage Yard Grade Leveling, Safe Tier Stacking & OSHA Safety Protocol
1. Storage Yard Concrete Paving & Drainage - Yard foundation must be compacted (compaction ratio $\ge$ 0.95) and paved with $\ge$ 180 mm Grade C25 concrete slab, rated for $\ge$ 15...
Cần Hỗ trợ Kỹ thuật?
Nếu bạn gặp bất kỳ vấn đề nào trong quá trình lắp đặt, vận hành hoặc bảo trì thiết bị, đội ngũ kỹ thuật của chúng tôi sẵn sàng cung cấp hỗ trợ chuyên nghiệp.